Home/ Blog/ SS hose/ Stainless Steel vs Rubber vs PTFE Hose: Which Should You Use?

Stainless Steel vs Rubber vs PTFE Hose: Which Should You Use?

Published November 6, 2026 · Updated November 21, 2026

SS hose · Comparing materials

Stainless steel, rubber or PTFE: three different answers to “I need a flexible line”

No material wins everywhere. Each one has a bore range, a pressure range and a kind of movement it handles well, and the right one depends on your duty.

Bore range of SS flexible hose, PTFE hose and rubber steam hoseSS flexible hose runs 6 to 150 millimetres. SS PTFE Teflon hose runs 3.5 to 50 millimetres. One wire braid rubber steam hose runs 12.5 to 50 millimetres.SS flexible6 to 150 mmPTFE3.5 to 50 mmRubber (steam)12.5 to 50 mmBore range on one scale, in millimetres
Where each hose family sits by bore. Rubber is shown by one product, one wire braid steam hose.

Flexihose makes all three. Flexihose SS flexible hose pipe: annular corrugated, with or without braiding · tube AISI 304, 321, 316L · EN ISO 10380 · catalogue table, read as braided: 6 to 150 mm, 110 BAR working at 6 mm, 10 BAR at 150 mm

Quick answer

Use stainless steel hose for fixed metal pipework that needs a flexible section. Use SS PTFE Teflon hose for small bores, chemicals and published high temperature, with a catalogue range of -65 C to +260 C. Use rubber hose where the hose is handled, dragged and coiled by people. Stainless steel is not automatically better than rubber.

“Are stainless steel hoses better than rubber?” comes up constantly, and the honest answer is that it depends what the hose has to do. We make all three: SS flexible hose pipe, SS PTFE Teflon hose and a range of rubber hose. So we have no reason to push one. This guide compares them using our own catalogue figures.

On steam specifically: we have a separate guide, rubber vs stainless steel steam hose. This one is the general comparison.

The three hose families compared

How the three compare. Figures are from our catalogue; rubber varies by product, so one wire braid steam hose is used as the example.

SS flexible hoseSS PTFE Teflon hoseRubber hose (steam example)
ProductCorrugated stainless steel tubeSS PTFE Teflon hose, as the catalogue names itEPDM rubber, steel wire braid
Bore range6 mm to 150 mm3.5 mm to 50 mm (1/8″ to 2″)12.5 mm to 50 mm (1/2″ to 2″)
Highest working pressure in range110 BAR at 6 mm3625 PSI / 250 BAR at 1/8″145 PSI / 10 BAR
Published service temperatureNot published-65 C to +260 C-40 C to +195 C
Handles bestVibration and movement in fixed pipeworkChemicals and heat at small boresBeing moved, dragged and coiled
Watch out forTwisting, tight bendsBend radius, which rises sharply with boreCover damage, and staying inside its rating

FLEXI HOSE Product Catalogue 2026-2027. Rubber figures are one wire braid steam hose only, which exceeds IS 10655 Type 2 and is not BIS licensed. Other rubber hoses, including suction and discharge hose, have their own bores and ratings: see our product range.

Pressure at similar bores

The headline numbers are misleading because each family peaks at a different size. Compare at a similar bore instead.

Catalogue working pressure at three similar bores12 mm SS 80 BAR against 12.7 mm PTFE 113 BAR. 25 mm SS 45 BAR against 25.4 mm PTFE 50 BAR. 50 mm SS 30 BAR against 50 mm PTFE 30 BAR. One wire braid steam hose 10 BAR at each bore from 12.5 to 50 mm.12 mm SS80 BAR12.7 mm PTFE1631 PSI / 113 BAR25 mm SS45 BAR25.4 mm PTFE725 PSI / 50 BAR50 mm SS30 BAR50 mm PTFE435 PSI / 30 BAR50 mm steam145 PSI / 10 BAR
Working pressure from our catalogue. SS figures are printed in BAR only; PTFE and steam show the catalogue’s own PSI and BAR pair.

FLEXI HOSE Product Catalogue 2026-2027. Bores are the nearest catalogue sizes, not identical.

At small bores PTFE carries more, and by 50 mm the two are level at 30 BAR. Of the products compared here, only the stainless steel hose continues above 50 mm, up to 150 mm at 10 BAR. For all fifteen SS sizes, see the SS flexible hose size chart.

Where each hose wins

A first pass by duty.

  • Stainless steelFixed metal pipeworkPump and compressor connections and thermal movement. The wall is metal throughout, so there is no lining to swell.
  • PTFEChemicals at small boresPublished -65 C to +260 C, with a wide chemical duty listed in our catalogue, and small bend radius at the smallest sizes.
  • RubberHoses people moveWash-down, transfer and site work, where a hose is dragged, coiled and handled every day.

Handling is the point most comparisons leave out. A corrugated metal hose is designed to be installed and left to do its job. It does not like being dragged, kinked or repeatedly twisted, which Penflex’s hose handling guide warns about directly. A rubber hose is built for that kind of handling. For the metal hose itself, BOA Group’s metal hose guide lists the sectors it is used in, from HVAC to oil and gas. Where the hose goes is explained in where SS flexible hoses are used.

How long does each one last?

We do not publish a service life for any of these, because the honest answer depends on the duty. The same stainless hose can have very different lives in the same spot, depending on whether it was fitted with a proper bend or with a twist in it. Replace on inspection, not by a number off a web page.

How to choose a hose family

Four questions in order.

  1. 1Does a person move it?If it is dragged or coiled in use, start with rubber.
  2. 2Bore above 50 mm?Our SS flexible hose continues to 150 mm. For suction and discharge duties, ask about rubber too.
  3. 3Aggressive chemical or published heat rating needed?Look at PTFE, whose range is printed in the catalogue.
  4. 4Fixed line with movement?Stainless steel. Then choose the grade and the braid.

If stainless steel is the answer, the next choices are the steel grade and braided or unbraided. It is worth knowing the families sit under different tariff headings too, covered in the SS hose HSN code guide.

Tell us the duty, not the material

Because we make all three, you can send us the duty and let us suggest the family: bore, pressure, temperature, medium and how the hose moves. Start with our stainless steel flexible hose or what an SS flexible hose is.

↑ Back to top

FAQ

Are stainless steel hoses better than rubber hoses?

Not in every case. Stainless steel suits fixed metal pipework, vibration and thermal movement. Rubber suits hoses that people move, drag and coil. Stainless is rarely a good fit for a hose that gets dragged around a site.

Are braided hoses better than rubber?

Braided describes the reinforcement and rubber describes the tube, so they are not opposites. Many rubber hoses are wire braided too. An SS braided hose has a metal tube and a metal braid, which suits fixed pipework but is not built for rough handling.

How long do stainless steel braided hoses last?

We do not publish a service life, because it depends on the duty, the installation and the medium. Twisting, over-bending and corrosive surroundings are the usual causes of early failure. Inspect regularly and replace on condition.

Which hose material is best?

There is no single best material. Choose by duty: who or what moves the hose, the bore, the pressure, the temperature and the medium. We make stainless steel, PTFE and rubber hose, and can suggest a family once we know those facts.

Is PTFE hose the same as stainless steel hose?

No. As a general type, a PTFE hose carries the medium in a PTFE tube, often with a stainless steel braid over it. An SS flexible hose has a corrugated stainless steel tube. They can look similar from the outside, but our catalogue lists them in separate tables.

PS

Pushkar Singh

Digital Marketing Lead, Vardhman Hydraulic Hoses Pvt. Ltd.

Pushkar Singh is Digital Marketing Lead at Vardhman Hydraulic Hoses Pvt. Ltd. (Flexihose India), where he has worked for over a year and a half.

More about the author

Have a question this guide didn't answer?

Send us your bore size, pressure and application and we'll recommend the right hose.