Home/ Blog/ SS hose/ How to Install a Metal Hose So It Doesn’t Crack Early

How to Install a Metal Hose So It Doesn’t Crack Early

Published November 6, 2026 · Updated November 21, 2026

SS hose · Installation

How to install a metal hose so it doesn’t crack early

Many early failures are not faults in the hose. They come from how it was fitted. One twist or one tight bend near the end can be enough, and much of this is avoidable.

The same hose fitted with a twist and fitted straightLeft: a hose held at both ends with a twist running through it, marked wrong. Right: the same hose with a smooth bend, supported and marked right.Twisted during tighteningBend in the middle, no twist
A common mistake, and the fix. Drawings are schematic.

Flexihose SS flexible hose pipe: annular corrugated, with or without braiding · tube AISI 304, 321, 316L · EN ISO 10380 · catalogue table, read as braided: 6 to 150 mm, 110 BAR working at 6 mm, 10 BAR at 150 mm

Quick answer

To install a metal hose: plan a bend no tighter than the listed radius and away from the fittings, anchor and support the pipework, make up one joint with the hose supported and unloaded, then tighten the second using two wrenches so the hose does not twist. Never stretch or compress the hose to fit. Keep weld splatter off the braid.

We make SS flexible hose pipe in Bhiwadi, and the advice below comes from the published installation guidance of metal hose makers, which agrees on the main points. BOA Group’s guide puts the main rule simply: avoid torsion, because it leads to early failure. Read this before the hose goes in, and share it with whoever is fitting it.

Safety and scope. Never work on a line that has not been isolated and depressurised. This is general guidance for corrugated metal hose. Your plant’s procedures, the pipework code for your line and any permit system come first. Pressure testing and commissioning follow your site’s procedure.

How to install a metal hose in seven steps

  1. Make the line safe and check the hose. When replacing a hose, isolate, depressurise and drain the line under your site’s permit system first. Then confirm size, length, grade, braid and both ends. Look for kinks, dents and broken braid wires.
  2. Plan the bend. Find the bend radius for your size: S for a static bend, F for a hose that moves, vibrates or sees pressure pulses. Allow enough length to keep the bend inside it and away from the fittings.
  3. Anchor and support the pipework. Make sure the pipe, not the hose, carries the weight. A hose taking movement needs anchors or guides.
  4. Fit one end with the hose supported and unloaded. Make up the first joint with the hose supported, so its weight is not hanging on the fitting and it can settle without any built-in twist.
  5. Make up the second joint without twisting. Use two wrenches on a union: one to hold, one to tighten. Wrench on the fitting’s flats only. On a flange, use a loose or lap joint flange if the holes need lining up.
  6. Protect it from site damage. Keep weld splatter, grinding sparks and corrosive sprays away from the braid. Lift the hose rather than dragging it.
  7. Inspect it in service. Look for broken braid wires, kinks, leaks at the fittings and corrosion. Replace on condition.

For step 2, here is what the bend limits look like at three common sizes. All fifteen are in our SS flexible hose size chart.

Minimum bend radius at three sizes. S is a bend made once at installation. F is a hose that moves, vibrates or sees pressure pulses.

SizeBend radius SBend radius F
25 mm80 mm205 mm
50 mm160 mm325 mm
100 mm280 mm560 mm

FLEXI HOSE Product Catalogue 2026-2027, section 5.1.

Six mistakes that crack a metal hose

Six installation mistakesBending right next to the fitting, bending tighter than the listed radius, stretching or compressing to fit, leaving the hose unsupported so it sags, wrenching on the hose or collar, and letting weld splatter reach the braid.Bending at the fittingTighter than the radiusStretched to fitSagging, no supportWrench on the hoseWeld splatter on braid
All six appear in manufacturers’ handling guidance. Drawings are schematic.

Based on the Penflex hose handling guide and BOA Group metal hose guide.

  • Bending at the fitting. Penflex advises avoiding sharp bends especially near the end fittings. Put the bend in the middle of the hose.
  • Going below the listed radius. Do not bend tighter than the table, even once. The same guide warns that repeated bending below a maker’s listed radius causes premature failure.
  • Stretching or compressing to fit. Don’t make the hose the adjustment. Order the correct length.
  • No support. Excess weight can compress the hose and relax the braid’s tension, and a horizontal loop needs support so it does not sag.
  • A wrench in the wrong place. Wrench on the fitting’s hex flats only, never on the hose or collar.
  • Site damage. Store and fit the hose away from weld splatter, corrosive fumes and sprays, and lift it rather than dragging it.

Getting the movement right

If the hose is there to take movement, the direction matters as much as the fit. Flexline’s installation notes say pipe motion must be perpendicular to the hose’s centre line. They also warn against using a hose to compensate for bolt-hole misalignment, so fix the alignment instead. Which duties suit a hose at all is in where SS flexible hoses are used.

An unbraided hose has an extra limit: it extends under pressure, because nothing holds its ends together. Our braided vs corrugated guide explains why. Your choice of end also helps here: flanges, unions and swivel ends can reduce the twist risk before anyone picks up a wrench.

Can you cut an SS braided hose on site?

It is best not to. The braid is secured at the end joint, and that joint is what carries the pressure load. Cut a finished assembly and you remove the joint. Cutting a hose also frays the braid and leaves a raw corrugated end that has to be prepared and re-terminated properly. Order the right overall length, or send us the measurement and we will make the assembly up.

What to look for in service

  • Broken braid wires, especially near the ends. The braid carries the load, so this is not cosmetic.
  • Kinks or flat spots. A kinked corrugation is a fatigue point.
  • Weeping at a fitting or through the braid.
  • Corrosion, which may mean a grade problem. See SS 304 vs 321 vs 316L.

We do not publish a replacement interval, because life depends on duty and installation. Take a suspect hose out of pressure service and replace it according to your site’s procedure.

Fit it once

Getting these right can be the difference between a long-lived hose and a repeat order. When you need a replacement, send the size, length and ends for your SS flexible hose pipe. If the terms here are new, read what an SS flexible hose is. Comparing replacement quotes? See SS flexible hose pipe prices in India. Reordering across states? The HSN code guide covers the paperwork, and types of metal hose covers the other hose forms you may find in service.

↑ Back to top

FAQ

How do you install a flexible metal hose?

Plan a bend no tighter than the listed radius and away from the fittings, support the pipework, fit one end with the hose supported and unloaded, then make up the other end using two wrenches so the hose does not twist. Do not stretch or compress it to fit.

Why does a metal hose fail early?

The usual causes are twist during installation, bending tighter than the listed radius, bending right at the fitting, movement in the wrong direction, and corrosion from the wrong grade. These are installation or selection problems rather than faults in the hose.

How do you cut an SS braided hose?

We advise against cutting a finished assembly, because the end joint carries the pressure load. Order the correct length instead. If a hose must be shortened, it needs to be properly re-terminated by someone equipped to do that, and then tested according to your site's procedure.

Can a metal hose be installed in a vertical line?

Yes, provided the pipework carries the weight and the hose is not compressed by it. Penflex warns that excess weight can compress the hose and relax the braid tension, so support the line on both sides.

How often should a metal hose be inspected?

Follow your site's inspection procedure. We do not publish a fixed interval. Look for broken braid wires, kinks, weeping at the fittings and corrosion, and replace on condition.

PS

Pushkar Singh

Digital Marketing Lead, Vardhman Hydraulic Hoses Pvt. Ltd.

Pushkar Singh is Digital Marketing Lead at Vardhman Hydraulic Hoses Pvt. Ltd. (Flexihose India), where he has worked for over a year and a half.

More about the author

Have a question this guide didn't answer?

Send us your bore size, pressure and application and we'll recommend the right hose.