SS 304, 321 or 316L: what actually changes in a flexible hose
The three grades look identical on the rack. The difference is a small amount of molybdenum in one and titanium in another, and whether your medium makes that difference matter.
Flexihose SS flexible hose pipe: annular corrugated, with or without braiding · tube AISI 304, 321, 316L · EN ISO 10380 · catalogue table, read as braided: 6 to 150 mm, 110 BAR working at 6 mm, 10 BAR at 150 mm
Quick answer
Choose AISI 304 for general duties such as water, air and oils where chlorides are low. Consider AISI 316L where chlorides or more aggressive chemicals are present, because its molybdenum raises pitting resistance, though it is not immune. Choose AISI 321 where intergranular corrosion after heating is the concern, because titanium stabilises it. Tell the supplier the medium and let them confirm.
We make SS flexible hose pipe with the tube in AISI 304, 321 or 316L, and the braid in AISI 304 or 316L. Buyers often default to “316, to be safe”, or to 304 because it is what they know. This guide explains what the alloys do differently, using published producer data so you can check it, and gives a way to choose.
The three grades compared
What separates the grades.
| AISI 304 | AISI 321 | AISI 316L | |
|---|---|---|---|
| In one line | All-purpose chromium-nickel steel | 304-type steel stabilised with titanium | Low-carbon steel with molybdenum |
| Typical Cr / Ni % | 18.1 / 8.1 | 17.3 / 9.1 | 17.2 / 10.1 |
| Added element | None | Titanium | Molybdenum, typically 2.1 % |
| PRE (pitting index) | 18 | 17 | 24 |
| Usually considered for | Water, air, oils, general lines | Where intergranular corrosion after heating is the concern | Moderate chlorides and more aggressive media |
| In our range | Tube and braid | Tube only | Tube and braid |
Typical values: Outokumpu Core range datasheet (304, 321) and Outokumpu Supra range brochure (316L). Read 5 November 2026.
What molybdenum does: why 316L resists pitting better than 304
Stainless steel resists corrosion because of a thin chromium-rich surface film. Chlorides can break that film locally and start a pit. Molybdenum strengthens the steel against this, which is why it appears in the pitting resistance equivalent, the index used to rank grades. The worldstainless corrosion module uses that index to compare grades, and Outokumpu’s published figures put 316L at 24 against 18 for 304.
Outokumpu datasheets, as above.
The hose wall makes this matter more than it would in a thick pipe. A corrugated tube is thin, so a pit has less metal to get through. If salt or chloride-bearing fluid is near the line, start the conversation at 316L. Better than 304 does not mean immune. Seawater, hot chlorides and stagnant conditions can still attack it, through pitting, crevice corrosion under the braid or stress corrosion cracking, so those duties need an engineering review of the grade rather than a default choice. The “L” means low carbon, typically 0.02 % against 0.04 % for 304.
What titanium does: where 321 fits
Grade 321 is close to 304 with titanium added. Outokumpu describes it as titanium-stabilized with improved intergranular corrosion resistance for an extended temperature range. In plain terms: heating some stainless steels lets chromium combine with carbon at the grain boundaries, leaving the metal next to them short of chromium. Titanium ties up the carbon first.
Note what 321 does not give you. Its PRE is 17, so it is not a chloride grade. And although the steel has this high-temperature property, our catalogue prints no service temperature for the hose in any grade. Give us the operating temperature so that we can check that duty with the works, as explained in where SS flexible hoses are used.
How to choose the grade
A first pass by medium and environment. Your supplier confirms it.
- StartName the mediumWhat flows through the hose, its concentration, and what surrounds the hose outside.
- If chloridesStart at 316L, then reviewBetter than 304, not immune. Seawater and hot chlorides need an engineering review.
- If heat cyclesAsk about 321Where intergranular corrosion after heating is the stated concern.
- Otherwise304 is the usual startWater, air and oils in a general plant, with low chlorides.
Two practical points. First, think about the outside as well as the inside: a 304 tube in a clean fluid can still pit from a salty atmosphere. Second, match the braid. Our braid comes in 304 or 316L, and a braid is made of fine wire, so it should not be the weak point in a corrosive location.
Grade also affects the quote. Our guide to SS flexible hose pipe prices covers why, and stainless steel vs rubber vs PTFE hose covers duties where another hose material suits better than any stainless grade.
SS flexible hose guides
- SS flexible hose pipeSizes, grades and how to enquire
- What is an SS flexible hose?Construction, parts and the names buyers use
- SS braided vs corrugated hoseWhich one a pressure line needs
- SS flexible hose size chart6 to 150 mm, pressure and bend radius
- Stainless steel vs rubber vs PTFE hoseThree answers to one question
- Where SS flexible hoses are usedThe movement problems they solve
- SS hose end fittingsThreaded, welded, flanged and swivel
- Metal hose installation guideSix mistakes that crack a hose
- Types of metal hoseAnnular, helical and stripwound
- SS braided hose HSN code and GST8307.10 and how to read it
- SS flexible hose pipe price in IndiaWhy per-metre quotes differ
Send the medium, not just the grade
The most useful line on an enquiry is what the hose will carry. With that, the size and the pressure, we can confirm the grade for your stainless steel flexible hose. The braided vs corrugated guide covers the next decision, and what an SS flexible hose is covers the basics.
FAQ
Which is better, SS 316 or SS 304?
Neither is better everywhere. 316L has molybdenum, which raises pitting resistance, so it is usually considered first around chlorides and more aggressive chemicals, though seawater and hot chlorides still need an engineering review. 304 is the all-purpose grade for water, air and oils where chlorides are low, and using 316L there may add cost without adding value.
Is 304 stainless steel cheaper than 316?
Generally yes, because 316L contains molybdenum and more nickel, both of which are costly alloying elements. The size, length, braid and ends also move the price of a hose, so compare complete quotes rather than grades alone.
How can you tell if stainless steel is 304 or 316?
Not by looking at it, and a magnet is not reliable because both are austenitic grades. The reliable routes are the supplier's material documents or a positive material identification test, which reads the molybdenum content directly.
What does the L mean in 316L?
L means low carbon. Outokumpu's typical figure for 316L is 0.02 percent carbon, against 0.04 percent for its 304. Lower carbon reduces the risk of chromium carbides forming during welding.
Is a different pressure rating published for each grade?
No. Our catalogue prints one pressure table for the SS flexible hose, not one table per grade. If your duty is close to a limit, tell us the grade and the temperature and we will confirm it for that case.
Have a question this guide didn't answer?
Send us your bore size, pressure and application and we'll recommend the right hose.
