Home/ Blog/ SS hose/ What Is an SS Flexible Hose, and How Is It Built?

What Is an SS Flexible Hose, and How Is It Built?

Published November 6, 2026 · Updated November 21, 2026

SS hose · The basics

What an SS flexible hose is, and how it is built

A tube of thin stainless steel, formed into rings so it can bend. Add a wire braid to hold pressure and metal ends to connect it. That is the whole product, and each part does one job.

Layers of an SS flexible hose coming togetherA corrugated stainless steel tube on the left, a stainless steel wire braid sliding over it, and a flanged end fitting on the right. Numbered markers: 1 tube, 2 braid, 3 end fitting. 123Corrugated tubeWire braidEnd fitting
Three parts: the tube contains the medium, the braid carries the pressure load, the ends join it to the line.

Flexihose SS flexible hose pipe: annular corrugated, with or without braiding · tube AISI 304, 321, 316L · EN ISO 10380 · catalogue table, read as braided: 6 to 150 mm, 110 BAR working at 6 mm, 10 BAR at 150 mm

Quick answer

An SS flexible hose is a thin stainless steel tube, corrugated into rings so it can bend, usually covered with a stainless steel wire braid and finished with metal end fittings. It joins pipework or equipment where a rigid pipe cannot take movement or vibration. Buyers also call it an SS hose pipe, a metal hose or an SS bellow hose.

Most people meet an SS flexible hose when a rigid line keeps cracking at a pump, or when a drawing calls for “metal hose” and nobody on site has specified one before. We make SS flexible hose pipe in Bhiwadi, Rajasthan, so this guide explains the product the way we describe it to a buyer: what the parts are, how a metal wall manages to bend, and what the different names mean. It stays with what the hose is. Choosing one is covered in the guides linked along the way.

An SS flexible hose in one paragraph

SS stands for stainless steel. A flexible hose in this material starts as a thin tube, which is then corrugated so the wall folds like a concertina. Without the folds it would be a rigid pipe. With them, it can flex, absorb vibration and connect two points that do not line up perfectly. The international reference for this product is ISO 10380, which sets minimum requirements for the design, manufacture, testing and installation of corrugated metal hose and hose assemblies. Our catalogue cites EN ISO 10380.

Five names you will see on enquiries and drawings. All five usually point at the same product family.

  • Trade nameSS hose pipeA common term on Indian purchase orders.
  • Formal nameStainless steel flexible hoseThe term used on drawings and in specifications.
  • By materialMetal hoseCovers other metals too, so confirm the grade.
  • By formCorrugated metal hoseDescribes the wall. Often unbraided unless stated.
  • Indian tradeSS bellow hoseNamed for the rings, which look like a bellows.

The three parts of an SS flexible hose

1. The corrugated tube

The tube carries the medium and keeps it in. Our catalogue describes annular corrugated hose produced from longitudinally welded tubes that are then corrugated mechanically, in AISI 304, 321 or 316L. Annular means each corrugation is a separate closed ring. The other form, helical, runs as one continuous spiral, and our guide to the types of metal hose sets the forms side by side.

2. The wire braid

The braid is an optional sleeve of stainless steel wire, AISI 304 or 316L in our range, woven over the tube. Metal hose makers describe the braid as the part that carries the load: BOA Group’s metal hose guide says the pressure resistance of braided hose is many times that of hose without braiding. Whether you need one is the subject of our SS braided vs corrugated hose guide.

3. The end fittings

Our catalogue lists threaded ends and welded connections, with flanges and swivel fittings to customer specification. The ends are not an accessory. They are how the pressure load leaves the braid and enters the pipework, and our guide to SS hose end fittings covers how to specify each type.

How a metal wall manages to bend

Stainless steel does not stretch much, so the bending comes from geometry. The rings open slightly on the outside of a bend and close on the inside, and the metal between them flexes a little. That is why the corrugation count matters: our catalogue prints 480 corrugations per metre at 6 mm and 69 at 150 mm.

Corrugations opening on the outside of a bendA hose segment bends gently up and down. The rings on the outer side of the bend open and the rings on the inner side close, which is how a metal wall can flex. Rings open on the outside of the bend and close on the inside. The metal itself barely stretches.
The rings do the work. Drawing is schematic, not to scale.

It also explains the limit. Bend tighter than the rings can take and the metal itself has to yield, which is where fatigue cracks begin. So every size has a minimum bend radius, in two versions: S for a hose bent once and left, F for a hose that moves, vibrates or sees pressure pulses in service. At 25 mm our table gives 80 mm and 205 mm. All fifteen sizes are in our SS flexible hose size chart.

What an SS flexible hose is not

  • Not a bathroom connector. The short braided connectors sold for taps, geysers and washing machines share the look and the name. They are consumer plumbing parts, and they are not in our catalogue.
  • Not a rubber hose with a steel cover. The wall that holds the medium is metal all the way through, so there is no rubber lining in it. Stainless steel vs rubber vs PTFE hose compares the three.
  • Not a pipe that can be bent anywhere. It takes the movement it is installed for. Twisting it is the classic way to shorten its life, which our metal hose installation guide explains.

Where it does belong, from pump connections to thermal movement, is laid out in where SS flexible hoses are used.

What to do with this next

If a line needs one, three facts decide most of the specification: the size, whether it runs under pressure, and what flows through it. Send us those and we will tell you what fits from our SS flexible hose pipe range. For the grade question, start with SS 304 vs 321 vs 316L.

↑ Back to top

FAQ

What is SS hose?

SS hose is short for stainless steel hose. In industry it usually means an annular corrugated stainless steel tube, with or without a stainless steel wire braid, fitted with metal ends. It is used where a rigid pipe cannot take movement or vibration.

What is a metal hose?

A metal hose is a flexible hose whose wall is metal rather than rubber or plastic. The wall is corrugated or wound so that it can bend. Stainless steel is one of the materials used, so a metal hose order should always state the grade.

What is the difference between an SS hose and an SS pipe?

An SS pipe is rigid and is cut, welded or threaded into a fixed line. An SS hose has a corrugated wall, so it can bend and absorb movement. Hose is normally used for a short flexible section within a pipe system, not to replace the whole line.

What is an SS flexible hose made of?

Ours has a tube in AISI 304, 321 or 316L stainless steel and, where braided, a wire braid in AISI 304 or 316L. End fittings are threaded or welded, with flanges and swivel fittings made to customer specification.

What standard applies to SS flexible hose?

ISO 10380 is the international standard for corrugated metal hoses and hose assemblies. Our catalogue cites EN ISO 10380 for stainless steel corrugated flexible hose.

PS

Pushkar Singh

Digital Marketing Lead, Vardhman Hydraulic Hoses Pvt. Ltd.

Pushkar Singh is Digital Marketing Lead at Vardhman Hydraulic Hoses Pvt. Ltd. (Flexihose India), where he has worked for over a year and a half.

More about the author

Have a question this guide didn't answer?

Send us your bore size, pressure and application and we'll recommend the right hose.